Makita’s 40V max XGT 3-Speed 1/2 in. Driver-Drill, model GFD03, has been on sale since Makita announced it on July 7, 2026, and it now replaces the two-speed GFD01 on Makita’s US site. It lists 1,590 in.lbs. (180 N.m) of maximum torque, and one US dealer, Burns Tools, listed the GFD03SU1 kit at $389.00 USD on November 14.
What changed from the GFD01?
The big changes are a third gear and more torque. Makita’s GFD01Z page now marks that model discontinued and names the GFD03Z as its replacement. ToolNut’s listing for the GFD01 kit gives it 1,250 in-lbs, two speeds of 0 to 650 and 0 to 2,600 RPM, and a 41 and 21 setting electronic clutch.
Makita’s figures for the GFD03 below come from its GFD03Z product page; the GFD01 figures come from ToolNut’s listing.
| Spec | GFD03 (new) | GFD01 (replaced) |
|---|---|---|
| Max torque | 1,590 in.lbs. | 1,250 in-lbs |
| Speeds | 0 to 650, 0 to 1,800, 0 to 2,400 RPM | 0 to 650, 0 to 2,600 RPM |
| Clutch settings | 41 low, 30 medium, 21 high | 41 low, 21 high |
| Length | 7-3/4 in. | 7-1/8 in. |
| Weight with battery | 6.7 lbs. | not listed |
| Steel capacity | 13/16 in. | not compared |
The new middle gear is the practical gain. Makita says it gives twice the working speed of two-speed models in the medium range and up to twice the sustained power under heavy loads, both the maker’s own claims. The trade off is 5/8 in. of extra length.

Is the top speed 2,400 or 2,600 RPM?
Makita’s GFD03Z page, its press release and the IronPros announcement all give 0 to 2,400 RPM. Some spec tables, including the GFD03SU1 page and the Burns Tools listing, show 2,600 RPM, which matches the old GFD01’s top speed. Treat 2,400 RPM as the figure Makita states in its own feature text, and check the manual if top speed matters to you.
How much does it cost?
Makita still lists no price and sends buyers to a dealer finder. Burns Tools listed the GFD03SU1 kit at $389.00 USD on November 14, with the note that it ships from the manufacturer. No dealer price for the GFD03Z tool only version turned up in the listings checked for this story.
For comparison, ToolNut listed the outgoing GFD01D kit, which comes with a smaller 2.5Ah battery, at $529.00, out of stock and available to order. Prices vary widely by dealer, so compare several before buying.
What is in the kit?
According to Makita’s product page and the Burns Tools listing, the GFD03SU1 kit contains the GFD03Z drill, a BL4040F 40V max XGT 4.0Ah High Power Battery, a DC40RC fast charger, a side handle and a tool bag. The GFD03Z is the bare tool for people who already own XGT batteries.
The drill runs only on 40V max XGT batteries. Makita’s 18V LXT packs do not fit, so an LXT owner buying the GFD03 is starting a second battery system.
How does it compare with an 18V rival?
Milwaukee’s M18 FUEL 1/2 in. Drill/Driver 2903-20 lists 1,400 in-lbs and a length of 6.9 in. on Milwaukee’s page. The GFD03 claims 190 in.lbs. more torque and a third gear, while the Milwaukee is 0.85 in. shorter. Milwaukee’s page does not give a weight or speed figures for a direct comparison.
What else is built in?
Makita lists Active Feedback-sensing Technology (AFT), which stops the motor if the bit suddenly binds, plus XPT dust and water sealing, a reinforced gear housing, an all-metal keyless chuck, an LED light at the base and a redesigned side handle. The tool, battery and charger carry Makita’s 3-year limited warranty.
Should you get the GPH03 hammer version instead?
Only if you drill masonry. Makita’s GPH03 hammer driver-drill, released in February 2026, lists the same 1,590 in.lbs., the same three speed ranges and the same clutch settings, and adds a hammer mode. The GFD03 is the plain driver-drill, suited to wood, metal and fastening.
What is still unknown?
There are no published independent test results for the GFD03 in the trade sources we checked, and Makita has not stated a list price. Makita’s speed and power gains are its own claims until outlets measure them.
Who it suits
- Professional on XGT: a high torque drill with a medium gear, an electronic clutch and AFT. Check whether you need the GPH03’s hammer mode before choosing.
- GFD01 owner: the GFD03 adds a gear and 340 in.lbs., but if your GFD01 still works, the gain mostly matters for large bits and hole saws.
- LXT owner tempted by XGT: this is a heavy duty drill that needs a new battery system. Price two XGT packs and a charger before deciding.
- Serious DIYer: the kit is complete, but 6.7 lbs. with battery is heavy for overhead or all day light work. Hold one in a store first.
- Crew or fleet buyer: the GFD03Z bare tool avoids duplicate batteries if the crew already shares XGT packs.
Use Makita’s dealer finder to compare the GFD03SU1 kit and GFD03Z bare tool prices where you live, and check the manual’s speed table before relying on the top RPM figure.




