Makita’s BCC01 and BCC02 charging cases hold 8 or 12 XGT batteries and charge them four at a time from one wall outlet, and a US dealer, Ace Tool, listed each at $999 on November 14. Makita announced both in April 2026 for fleets, grounds crews and campus maintenance teams, so this is not a new launch; the question now is whether one is worth that price.

What do the BCC01 and BCC02 do?

Both cases charge one bank of four batteries, then move to the next. Makita says this keeps the wall circuit from overloading, and that each bank of four charges in as little as 90 minutes when the packs are 40V max XGT 2.5Ah batteries. Each port has its own charge indicator, and the plug in power supply (DC4002) is included.

Makita’s figures for the two models:

BCC01 BCC02
Battery ports 8 12
XGT batteries All 40V max XGT sizes 2.5Ah and 4.0Ah listed
18V LXT Yes, with ADP10 adapter per port (sold separately) No
Cases per dedicated 15A circuit Up to 4 (32 batteries) Up to 4 (48 batteries)
Weight without batteries 14.3 lbs 15.0 lbs
US price seen Nov 14 $999 (Ace Tool) $999 (Ace Tool)
Makita BCC02 12 port charging case with its lid on
Photo: Makita U.S.A.

Which batteries does the BCC02 really take?

This is the detail to check before ordering. Makita’s April press release says the BCC02 works with XGT batteries generally, but its BCC02 product page, and Ace Tool’s listing, name only the 2.5Ah and 4.0Ah sizes.

Power Tools Insider, in an article updated in September, lists 2.5Ah to 8.0Ah packs for both cases. Makita’s own BCC02 page is the narrower and more recent statement, so if your crew runs 5.0Ah or 8.0Ah packs, confirm with a dealer or choose the BCC01, which Makita says takes all XGT sizes.

Makita BCC01 charging case with the lid removed
Photo: Makita U.S.A.

How much does it really cost?

The case is only the start. On November 14, Ace Tool listed both models at $999, the same for 8 or 12 ports, so the BCC02 is the better value per port if your batteries fit it.

If you also run 18V LXT, the BCC01 needs an ADP10 adapter in each port that holds an LXT pack. Contractor Tool, a US dealer, listed the ADP10 at $44, so converting all eight ports would add about $352.

Outside the United States, Power Tools Insider reported European listings around €665 for the BCC01, and DPR Tools in the UK showed it at £399, reduced from £478.80, on November 14. Prices vary widely by market, so compare locally.

Is it better than a row of single chargers?

For a crew with many packs, it can be. Power Tools Insider notes that a DC40RA rapid charger handles one XGT battery at a time, about 45 minutes per battery by its estimate, so a three person crew ends up rotating packs by hand. A case turns that into a batch job: load it at the end of the shift and the packs are ready by morning.

The trade off is speed. A case charges four at a time, so twelve 2.5Ah packs take three banks, roughly four and a half hours on Makita’s 90 minute figure. Several single chargers on separate circuits would be faster, but each needs an outlet and a person to swap packs.

For context on other platforms, Milwaukee’s approach is different: its M18 and M12 Four Bay Simultaneous Super Charger, listed at $499 by Pro Tool Reviews, charges four packs at once quickly but does not store a fleet’s worth of batteries.

Charging case holding XGT batteries on a shelf with a charger
Photo: Makita U.S.A.

What else does the case do?

Makita built it to travel. The lid comes off for open shelf charging and can be locked (DPR Tools notes the padlock is not supplied), the handles retract, the case works upright or on its side, and it links to the MAKPAC stacking system. Makita says XGT digital communication watches for overload, over-discharge and overheating.

Open BCC02 charging case on a job site while a worker uses a drill
Photo: Makita U.S.A.

Who it suits

  • Fleet and grounds crews: the target reader. One dedicated 15A circuit for up to four cases suits a depot with limited power. Count how many packs you cycle in a day, and check that they are sizes the case accepts.
  • Contractors on both LXT and XGT: only the BCC01 takes LXT, and each LXT port needs a $44 adapter. Budget the adapters before comparing with buying another charger.
  • Crews on 2.5Ah and 4.0Ah XGT packs: the BCC02 gives 12 ports for the same $999 as the BCC01’s 8 at Ace Tool. Confirm your pack sizes first.
  • Pros new to XGT: a single DC40RA or a dual charger is the simpler start. A case makes sense once you own more than about eight packs.
  • DIYers and homeowners: skip it. Few households own enough 40V max batteries to fill even 8 ports, and the price buys several batteries instead.

What should you check next?

Read the battery compatibility line on Makita’s BCC02 page against your own packs, count any LXT batteries that would need ADP10 adapters, then ask a Makita dealer for the price and stock in your market.