Milwaukee’s M18 FUEL mid-torque impact wrench delivers up to 650 ft-lbs of nut-busting torque from a 6 inch long body that weighs 5.1 lbs with a 5.0Ah battery, and it has been on sale since late 2020. Trade site For Construction Pros covered the launch in October 2020, so this is not a new tool: it is the current mid-torque model that buyers compare against DEWALT, Makita and Ryobi.

Which models are there?

Milwaukee sells three versions that differ in anvil size and socket retention, according to its press release.

Model Anvil Nut-busting torque Fastening torque Weight with battery Replaced
2960-22 3/8 in. friction ring 600 ft-lbs 550 ft-lbs 5 lbs 2852
2962-22 1/2 in. friction ring 650 ft-lbs 550 ft-lbs 5.1 lbs 2861
2962P-22 1/2 in. pin detent 650 ft-lbs 550 ft-lbs 5.1 lbs 2860

All three are 6 inches long and list 0 to 2,575 rpm and 0 to 3,100 impacts per minute. A friction ring lets you swap sockets quickly by hand. A pin detent locks the socket on, which suits work where a dropped socket is a problem, such as at height.

What do the drive modes do?

Milwaukee lists four modes. Modes 1, 2 and 3 run up to 1,250, 1,950 and 2,575 rpm, giving you a lower setting for small fasteners that would snap at full power.

Mode 4 is the useful one for wheel work. In forward it stops at no more than 35 ft-lbs so lug nuts go on hand tight before you torque them with a wrench, and in reverse it hits with full power, then slows once the bolt breaks free so the nut does not fly off. Milwaukee also lists tri-LEDs around the anvil and a rating for environments up to 69kV.

How did it do in independent tests?

Pro Tool Reviews revisited the 2962 about five years after launch and ran it against nine other mid-torque wrenches. Its results:

Pro Tool Reviews test Milwaukee 2962 result
Break eight 1-1/2 in. lug nuts set at 500 ft-lbs 26.09 seconds, second behind DEWALT DCF891 (23.77 s)
Drive a lag bolt in 30 seconds 0.56 in. left proud; only the DEWALT sank it
Peak inertia torque 412.8 ft-lbs, fourth of ten
Head length 5.9 in., over an inch shorter than the DCF891

The outlet scored it 9.4 out of 10 and called it the best balance of power and size in the class, while noting that DEWALT’s wrench is stronger on raw breakaway. It also measured 3.5 lbs bare and 4.8 lbs with a 3.0Ah battery, which shows how much a smaller pack trims the weight.

How does it compare with DEWALT’s DCF891?

The DEWALT DCF891 trades size for more torque. DEWALT rates it at 800 ft-lbs breakaway and 600 ft-lbs fastening, at under 4 lbs for the tool alone, with a 3-year limited warranty, 1 year of free service and a 90-day satisfaction guarantee. Milwaukee’s 2962 is rated at 650 and 550 ft-lbs.

If the largest fasteners you meet are seized suspension bolts or truck lug nuts, the DEWALT’s extra breakaway torque counts. If you work in wheel wells and engine bays where length matters, the Milwaukee’s shorter head is the reason to choose it.

How much does it cost?

Milwaukee does not publish prices. Pro Tool Reviews listed $279 for the bare tool and $479 for a kit in its follow up review, and those are the most recent figures we found from an outlet. Each -22 kit includes the wrench, two M18 REDLITHIUM XC5.0 batteries, an M12 and M18 charger and a carrying case, per Milwaukee. A 2960-22CT kit uses smaller REDLITHIUM 2.0 compact packs.

Bare tools are sold as 2960-20, 2962-20 and 2962P-20, which makes sense if you already own M18 packs. Pro Tool Reviews reports a 5-year warranty and notes there is no ONE-KEY version.

What should you know before buying?

The wrench takes any M18 battery, but runtime and weight depend on the pack. A 5.0Ah pack gives the 5.1 lb figure Milwaukee quotes, while a compact pack makes it lighter and shorter running.

Milwaukee sells a protective boot (49-16-2960) that fits all three models and a lanyard loop (49-16-2962) for work at height. Fit the boot if the wrench will ride on painted surfaces or rims.

Who it suits

  • Auto and fleet mechanics on M18: the short head reaches into wheel wells and Mode 4 helps with lug nuts. Check whether 650 ft-lbs covers your most seized fasteners, since Milwaukee sells separate high torque wrenches above this range.
  • Heavy equipment and line workers: the pin detent 2962P-22 keeps sockets locked on, and the 69kV rating is listed by Milwaukee. Confirm that rating matches your site rules.
  • Buyers on DEWALT or undecided: the DCF891 posted the faster lug nut time and more breakaway torque in Pro Tool Reviews’ tests. Compare head length and battery cost before switching.
  • DIYers and home mechanics: a mid-torque wrench handles car wheels and most suspension work. If you do not own M18 batteries, price the kit against a bare tool plus a battery and charger.

Check the current bare tool and kit prices for 2962-20 and 2962-22 at your local Milwaukee dealer, and read Pro Tool Reviews’ full five year review for the complete test results.