If your crew bends a lot of 3/4 inch and 1 inch EMT for branch runs, Milwaukee’s M18 FUEL Branch Conduit Bender w/ AUTO-ZERO, model 5150-20, is aimed squarely at you. Milwaukee’s press release lists the kit at $2,999.99 in US dollars with two bending shoes, a tripod and a backformer, but no battery.
Milwaukee says the tool finds zero degrees by itself on every bend and can make up to 110 bends on 3/4 inch EMT with one M18 XC5.0 pack, sold separately. The press release gives no ship date, and the product pages reviewed on November 14 showed no price or stock, only a Where To Buy link.
What is in the $2,999.99 kit?
Milwaukee’s US press release and its Canadian product page list the same contents:
- M18 FUEL Branch Conduit Bender, 5150-20
- 3/4 inch EMT / 1/2 inch RMC bending shoe, 49-16-0034
- 1 inch EMT and 3/4 inch RMC bending shoe, 49-16-0001
- Tripod and backformer
Not in the box: a battery, a charger and a shoe for 1/2 inch EMT. The bender works only with Milwaukee’s own shoes, which are aluminum and install without tools, according to the release.
How much do extra shoes cost?
Each shoe is also sold on its own, and the release prices them in US dollars.
| Shoe | Part number | What it bends | Price |
|---|---|---|---|
| 1/2 inch EMT | 49-16-0012 | 1/2 inch EMT | $324.99 |
| 3/4 inch EMT / 1/2 inch RMC | 49-16-0034 | 3/4 inch EMT, 1/2 inch RMC | $349.99 |
| 1 inch EMT / 3/4 inch RMC | 49-16-0001 | 1 inch EMT, 3/4 inch RMC | $399.99 |
So covering every size the tool handles, 1/2 to 1 inch EMT and 1/2 to 3/4 inch RMC, means the kit plus the 1/2 inch EMT shoe: $3,324.98 at list, before a battery. A crew that wants a spare of its most used shoe should add $349.99 or $399.99.
What conduit can it bend?
It is built for branch work, not feeder pipe. Milwaukee says it bends galvanized EMT up to 1 inch and RMC up to 3/4 inch, and its product page and the release agree on that range. Nothing larger is claimed, so 1-1/4 inch and up still needs another bender.
How does AUTO-ZERO work?
AUTO-ZERO is a sensor that reads squeeze and sets zero degrees on its own. Milwaukee says it does this regardless of variance in the roller, the shoe and the conduit, so bends stay consistent over the life of the tool without manual zeroing.
The release also claims easier layout and planar alignment without walking around the tool, up to 2X faster application speeds and 10X less peak muscle effort on the lower back. These are Milwaukee’s numbers. The sources reviewed give no bend angle accuracy, bending speed or tool weight, and no named outlet has published test results, so treat them as unconfirmed.
How does it carry and set up?
Milwaukee describes a two-piece design for carrying and setup, with a tripod in the kit. It does not publish the weight of either piece, which matters if one person will move it between floors. Ask to see it at a distributor before you order.
Does it work with my M18 batteries?
Yes. It runs on M18 REDLITHIUM packs and uses a POWERSTATE brushless motor. The 110 bend figure is for 3/4 inch EMT with an M18 XC5.0, so real counts on 1 inch EMT, RMC or with other pack sizes will differ. Milwaukee Canada’s product page lists a 2-year tool warranty, overload protection through REDLINK PLUS Intelligence and ONE-KEY support. The US warranty term was not stated in the sources reviewed.
Who it suits
- Electrical contractors and production crews: the claimed consistency and lower strain matter most on repeated branch runs and offsets. Check the two included shoes match the sizes you bend most, and price the 1/2 inch EMT shoe if your jobs use it.
- Fleet and shop buyers: it shares batteries and chargers with M18 tools already on the truck. ONE-KEY support helps with tracking, but confirm warranty terms in your market, since Canada lists two years.
- Solo electricians on M18: the battery side is covered, but $2,999.99 buys the tool, two shoes and the stand only. Compare the time saved with what you bend in a typical month.
- Electricians not on M18: add a battery and charger to the cost, and weigh whether one tool justifies a new platform.
- Homeowners and occasional users: at this price and with claims aimed at production work, a hand bender is the sensible choice.
Still unknown: release date, tool weight, bend speed in seconds and angle accuracy.
What to check next
Open Milwaukee’s 5150-20 product page for your country, then ask your distributor for a price, a ship date and whether the 1/2 inch EMT shoe, 49-16-0012, is in stock. If you plan to bend 1 inch EMT or RMC all day, ask how many bends your usual pack size gives.




