If you nail casing, baseboard and crown into tight corners, the number that matters on DEWALT’s new DCN220B is 3.1 inches: that is how wide DEWALT lists this brushless 20V MAX XR 16GA straight finish nailer. On November 14, Tool Nut listed the bare tool in the US at $399.00 USD, in stock, with the battery and charger sold separately.

Power Tools Insider reported the DCN220 on September 1 and updated its report on November 11. DEWALT’s own product page still labels it “New” and shows no price.

What is the DCN220B?

It is a cordless nailer for 16GA straight finish nails from 1-1/4 inches to 2-1/2 inches, the gauge most trim carpenters use for casing, base and door jambs. DEWALT’s page lists these specs, and Tool Nut’s listing matches them.

Spec DCN220B, per DEWALT
Nails 16GA straight finish, 1-1/4 in. to 2-1/2 in.
Magazine 110 nails
Width 3.1 in.
Weight 5.7 lbs bare tool
Speed Up to 5 nails per second, measured with a DCBP034 battery
Firing modes Sequential and contact, selectable
In the box Nailer, three no-mar tips, belt hook, DCE044 chip adapter
Warranty 3-year limited, 1 year free service, 30-day satisfaction guarantee

The speed figure is DEWALT’s own claim with a battery sold separately, and DEWALT says results vary. Other controls include tool-free depth adjustment, a tool-free jam release, a stall release and a low-nail lockout LED that stops the tool before it dry fires. It is also TOOL CONNECT Chip-Ready, which is what the included chip adapter is for.

DEWALT DCN220B nailer seen from the other side, with the model label
Photo: DEWALT

How does it compare with the DCN662?

The main change is size. Power Tools Insider calls the DCN220 a direct successor to the DCN662 and says earlier 16 gauge models measure 4.4 to 5.8 inches wide, against 3.1 inches here. A slimmer nose matters when you need to see your line in a corner or between a casing and a wall.

The DCN662D1 is still sold as a kit, which is a different buy. DEWALT’s page for it lists a DCN662 nailer, a 2.0Ah DCB203 battery, a DCB112 charger and a kit bag, with a 3-year limited warranty, 1 year of free service and a 90-day satisfaction guarantee. Both tools take the same 1-1/4 to 2-1/2 inch 16GA straight nails, according to DEWALT.

The sources differ on one detail. Power Tools Insider’s FAQ calls the DCN662 an angled nailer, while DEWALT’s own DCN662D1 page names it a straight finish nailer. The DEWALT page is the one to trust here, but check the nail type on the box before you buy collated strips.

DEWALT DCN220B nailer, third product view
Photo: DEWALT

How does it compare with Milwaukee’s M18 FUEL nailer?

The closest straight 16GA rival is Milwaukee’s M18 FUEL 16 Gauge Straight Finish Nailer, 3020-20. Milwaukee’s page lists these specs, and the comparison below sets them against DEWALT’s.

DEWALT DCN220B Milwaukee 3020-20
Nail length 1-1/4 in. to 2-1/2 in. 1 in. to 2-1/2 in.
Magazine 110 nails 110 nails
Rated speed Up to 5 per second 3 per second
Nails per charge Not published Up to 700 on an M18 CP2.0
Width 3.1 in. Not listed
Weight 5.7 lbs bare Not listed

Milwaukee lists a nitrogen air spring and LED work light, and publishes a nails per charge figure that DEWALT does not. DEWALT publishes a width and weight that Milwaukee’s page does not. Neither set of claims has been checked by a named test outlet in the sources reviewed, so the real choice for most buyers is still the battery platform they already own.

DEWALT DCN220B nailer nose and magazine close up
Photo: DEWALT

How much does it cost?

On November 14, Tool Nut listed the DCN220B at $399.00 USD with free shipping and in stock. Power Tools Insider also gives $399 for the bare tool and expected listings at Amazon, Acme Tools and Home Depot. DEWALT’s page shows no price, and the sources give no price outside the US.

If you own no 20V MAX battery, add a battery and charger to that $399.

DEWALT DCN220B nailer, accessory view
Photo: DEWALT

Who it suits

  • Trim carpenters and finish crews already on 20V MAX: the 3.1 inch nose and 5.7 lb bare weight are the draw. Add your battery’s weight before judging balance, because DEWALT does not give a weight with a pack fitted.
  • Serious DIYers: $399 is for the bare tool. If you own no DEWALT batteries, the DCN662D1 kit with its battery and charger may be the easier start.
  • First time buyers: confirm you want 16GA, which leaves a larger hole than an 18GA brad nailer but holds heavier trim.
  • Milwaukee M18 owners: the 3020-20 also takes nails from 1 inch and runs on your packs, so a platform switch for the narrower nose rarely makes sense.
  • Crew and fleet buyers: the included chip adapter supports DEWALT’s TOOL CONNECT tracking, so check it fits the system your company already uses.
  • Owners of a DCN662: nothing in the sources says the older tool is outdated. The gain is size, so try the new nose on your own trim before you swap.

Still unknown: weight with a battery, runtime per charge, any firing delay, the depth adjustment range and independent test results.

What to do next

Open DEWALT’s DCN220B product page for stock in your market and compare it with the Tool Nut listing. If you buy for trim work, handle the nailer in a store with your usual battery fitted and check the nose against your casing.